收藏本站
ISO/IEC 14443 Type B-Compliant
64-Bit UID
The lower nibble of Param 3 is used to confirm the pro-
MSb
LSb
tocol type as specified in the lower nibble of the second
BIT 8
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
byte of the ATQB protocol info. Since ISO/IEC 14443-3
X
X
X
X
sets the upper nibble of Param 3 to 0000b, the Param 3
RESPONSE DATA
RATE (UPLINK)
REQUEST DATA
RATE (DOWNLINK)
RECEIVER FRAME SIZE CAPABILITY
value to be used for the MAX66000 in the ATTRIB
request is 01h.
Param 4 assigns the slave the CID number that is used
Figure 25. Bit Assignments for Param 2 Byte
with the block transmission protocol to address one of
several slaves in the ACTIVE state. Figure 26 shows the
Param 4 bit assignments. Since the MAX66000 sup-
MSb
LSb
ports the CID field, the master can assign any number
BIT 8
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
in the range from 0 to 14. According to ISO/IEC 14443-
0
0
(FIXED)
0
0
CARD IDENTIFIER VALUE (CID)
3, code 15 is reserved.
The ATTRIB request frame contains one optional field,
called higher layer information (HLINF). This field can
Figure 26. Bit Assignments for Param 4 Byte
be used to include data as in the information field of the
ISO/IEC 14443 Type B block transmission protocol (see
Figure 10). If such data is present and the slave sup-
ports the HLINF field, then the slave processes the
SOF
INDICATOR
MBLI, CID
HL RESPONSE
( ≥ 0 BYTES)
CRC
(2 BYTES)
EOF
HLINF data and returns the result in its response to the
ATTRIB request. Typically, the ATTRIB request is trans-
mitted without HLINF field. The only HLINF data that the
Figure 27. ATTRIB Response Frame
MAX66000 accepts and processes is the Get UID com-
mand, code 30h.
If the ATTRIB request has a matching PUPI and a valid
FRAME WITHOUT CID
SOF COMMAND CRC
C2h (2 BYTES)
FRAME WITH CID
EOF
CRC, the slave transmits an ATTRIB response frame, as
shown in Figure 27. The upper nibble of the indicator,
also referred to as MBLI, is 0000b, telling that the slave
does not provide any information on its internal input
buffer size; the lower nibble returns the card identifier
value that the master has just assigned to the slave.
SOF
COMMAND
CAh
CID
(1 BYTE)
CRC
(2 BYTES)
EOF
The HL response field is optional. There are three
cases to be distinguished:
a) If there was no HLINF field in the ATTRIB request,
Figure 28. DESELECT Request and Response Frames
Param 2 informs the slave about the data rate that shall
be used for communication in the ACTIVE state and the
maximum frame size that the master can receive.
Figure 25 shows the bit assignments for the Param 2
byte. The MAX66000 supports the data rates of
105.9kbps (code 00b), 211.9kbps (code 01b),
423.75kbps (code 10b), and 847.5kbps (code 11b).
The master can choose different data rates for request
and response. Since it does not support chaining, the
MAX66000 ignores the frame size capability and
assumes that the master can receive frames as large
as specified in the ATQB response.
then there is no HL response field in the response.
b) If there was a Get UID command code (30h) in the
HLINF field of the ATTRIB request, then the HL
response field is identical to the Get UID response
information field (i.e., 00h followed by the 8-byte UID).
c) If the code in the HLINF field of the ATTRIB request
was different from 30h, then the response frame does
not contain an HL response field.
DESELECT Command
The DESELECT command is used to transition the slave
from the ACTIVE to the HALT state after the master has
completed the communication with the slave. There are
two versions of the deselect request frame, one without
CID and one with CID. Figure 28 shows both versions.
Figure 26 shows the CID format.
______________________________________________________________________________________
15
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAX66020K-000AA+ IC RFID UID 1KB TYPEB MEM KEYFOB
MAX66040K-000AA+ ISO CARD SECURE MEMORY
MAX6605MXK/V+T IC TEMP SENSOR ANLG LP SC70-5
MAX6608IUK+T IC TEMP SENSOR ANLG SOT23-5
MAX66100K-000AA+ IC RFID UID 64BIT TYPE B KEY FOB
MAX6611AUT+T IC TEMP SENS LOW PWR SOT23-6
MAX66120K-000AA+ IC RFID UID 1KB TYPEB MEM KEYFOB
MAX6612MXK+T IC TEMP SENSOR ANLG SC70-5
相关代理商/技术参数
MAX66000K-00AA+ 制造商:Maxim Integrated Products 功能描述:ISO/IEC 14443 TYPE B-COMPLIANT 64-BIT, UID FOB - Rail/Tube
MAX66020K-000AA+ 功能描述:RFID应答器 ISO/IEC 14443 Type B Comp 1Kb Mem Fob RoHS:否 制造商:Murata 存储容量:512 bit 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
MAX66020K-00AA+ 制造商:Maxim Integrated Products 功能描述:ISO/IEC 14443 TYPE B-COMPLIANT 1KB MEMORY FOB - Rail/Tube
MAX6602UE9A+ 功能描述:板上安装温度传感器 5Ch Precision Temperature Monitor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
MAX6602UE9A+T 功能描述:板上安装温度传感器 5Ch Precision Temperature Monitor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
MAX6603ATB 制造商:Maxim Integrated Products 功能描述:DUAL-CHANNEL PLATINUM RTD-TO-VOLTAG - Rail/Tube
MAX6603ATB+ 制造商:Maxim Integrated Products 功能描述:RTD TO VOLT SGNL CONDITIONER 10TDFN EP - Rail/Tube
MAX6603ATB+T 功能描述:板上安装温度传感器 RTD-to-Voltage Signal Conditioner RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor